|Product>>8051 MicroController>>STC15F2K60S2 series|
Enhanced 8051 Central Processing Unit, 1T, single clock per machine cycle, faster 8~12 times
than the rate of
a traditional 8051.
STC15F2K60S2 series: 5.5V ~ 4.2V.
STC15F2K60S2 series: 3.6V ~ 2.4V.
capability,can be repeatedly erased more than 100 thousand times.
per second, 3
channels PWM also can be used as 3 channels D/A Converter(DAC).
---- can be used as 3 Times or 3 external Interrupts
(which can be generated on
rising or falling edge)or 3 channels D/A Converter
(each channel of which takes less than 0.6% system time )
of accuracy (which takes less than 0.4% system time )
so that external reset curcuit
can be completely removed.
in normal temperature and wide frenquency adjustable between 5MHz and 35MHz (5.5296MHz /
11.0592MHz / 22.1184MHz / 33.1776MHz).
--UART1(RxD/P3.0, TxD/P3.1) can be switched to (RxD_2/P3.6, TxD_2/P3.7),
also can be switched to (RxD_3/P1.6, TxD_3/P1.7);
--UART2(RxD2/P1.0, TxD2/P1.1) can be switched to (RxD2_2/P4.6, TxD2_2/P4.7).
Stop/Power- Down mode.
Timers which can wake up stop/power-down mode: have internal low-power special wake-up Timer.
INT0/P3.2, INT1/P3.3 (INT0/INT1, may begenerated on both rising and falling edges),
INT2/P3.6, INT3/P3.7, INT4/P3.0 (INT2 /INT3/INT4, only be generated on falling edge);
pins CCP0/CCP1/CCP2; pins T0/T1/T2(their falling edge can wake up
if T0/T1/T2 have been enabled before power-down mode, but no interrupts can be generatetd);
low-power special wake-up Timer.
with Timer0/Timer1 of traditional 8051)
T0/T1/T2 all can independently achieve external programmable clock output 3 channels) .
3 channels CCP PCA PWM also can be used as three Timers
or the input clock of external pin):
The Programmable clock output of T0 is on P3.5/T0CLKO (output by dividing the frequency of the
internal system clock or the input clock of external pin T0/P3.4)
The Programmable clock output of T1 is on P3.4/T1CLKO (output by dividing the frequency of the
internal system clock or the input clock of external pin T1/P3.5)
The Programmable clock output of T2 is on P3.0/T2CLKO (output by dividing the frequency of the
internal system clock or the input clock of external pin T2/P3.1)
Three timers/counters in above all can be output by dividing the frequency from 1 to 65536.
The Programmable clock output of master clock is on P5.4/MCLKO, and its frequency can be divided
into MCLK/1, MCLK/2, MCLK/4.
The master clock can either be internal R/C clock or the external input clock or the external crystal
MCLK is the frequency of master clock. MCLKO is the output of master clock.
(traditional 8051 I/O ports mode) after reset, and can be set to four modes: quasi_bidirectional /weak
pull-up, strong pushpull/ strong pull-up, input-only/high-impedance and open drain.
the driving ability of each I/O port can be up to 20mA, but it don't exceed this maximum 120mA that
the current of the whole chip of 40-pin or more than 40-pin MCU, while 90mA that the current of the
of 16-pin or more than 16-pin MCU or 32-pin or less than 32-pin MCU.
General Overview: STC15F2K32S2_Features.pdf
Data Sheet: STC15F2K60S2.pdf
ISP programming software ：STC ISP programming software (v6.28)
|8 bit MicroController|
|32 bit MicroController|
|STC32 ARM series|
|Smart Card ICs|
|Discretes and Logic|
|STC15F2K60S2 series Selection Table|
|Copy right ©2014-2017 stcmicro.com, All Rights Reserved Tel: +86(10) 86974238 E-mail:firstname.lastname@example.org|